ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º R-G-B 9-PIN TO COMPOSITE VIDEO CONVERTER º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ I bought a computer with a built-in CGA video driver. I expected to use the composite, "1-pin" output to drive my old reliable amber composite monitor. Surprise! No composite output, only the TTL RGB 9-pin jack. I wasn't about to blow $250 to $300 for a 9-pin RGB monitor on my "spare" PC. Later, a friend's EGA monitor expired, and he needed something cheap to get by on till his EGA was fixed. An old composite monitor was the right price, but how to hook it to the 9-pin jack? Alligator clipping the connectors together doesn't work. There are four video signals on the 9-pin connector, with 4 volt signals on each. There are two sync signals, each too strong and the wrong polarity. I could have used an array of chips to get precision NTSC standard composite video. But all I wanted was a stable raster, crisp letters, and workable graphics. Also, I wanted a real "minimal" solution, that worked well. I puzzled a bit, and came up with an adapter that converts 9-pin CGA RGB signals to nice clean one pin monochrome composite video, with the colors represented by a 16 value `grey scale'. It cost me less than ten bucks and an hour's time to put together. The entire circuit was built inside the 9-pin plug's hood. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º CIRCUIT THEORY º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ The four TTL digital video signals are fed into a four bit Digital/Analog converter. This produces a 16 step one volt analog signal suitable for the monochrome composite monitor. The two vertical and horizontal sync signals are OR-ed together and fed into an inverter. This inverter is biased to produce a suitable one third volt composite negative sync pulse. Four resistors make the four bit Digital to Analog converter. Two resistors make the OR gate. One transistor and one resistor make the sync inverter. What could be simpler? Despite its simplicity, this circuit produces a rock-solid display on most monitors. All 128 pairs of foreground and background colors can be distinguished. Pixels are displayed crisply, with no visible fuzz around the edges. The image from this adapter is better than the composite output from my "genuine" CGA card, except it lacks color. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Page 1 R-G-B to Composite Converter (C) 1990 Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º SCHEMATIC DRAWING º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Pin# Function Resistors Transistor Output ÍÍÍÍ ÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍÍÍÍÍ ÍÍÍÍÍÍ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ+5volts<ÄÄÄÄ< ÀÄÄÄ680ohmÄÄÄÄÄÄ¿ Pin 6 IntensityÄÄÄ220ohmÄÄÄÄÄÄ´ Pin 3 RedÄÄÄÄÄÄÄÄÄ470ohmÄÄÄÄÄÄÅÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ>CompVideoÄÄ> Pin 4 GreenÄÄÄÄÄÄÄ1KohmÄÄÄÄÄÄÄ´ ³ Pin 5 BlueÄÄÄÄÄÄÄÄ1.5KohmÄÄÄÄÄÙ ³ ³ ³ ÉÍÍÍÍÍÍÍÍÍÍ» Pin 8 HsyncÄÄÄÄÄÄÄ1KohmÄÄÄÄÄÄÄ¿ ÀÄÄÄĺ C º ÃÄÄÄÄÄÄÄÄĺ B 2N2222º Pin 9 VsyncÄÄÄÄÄÄÄ1KohmÄÄÄÄÄÄÄÙ ÚÄÄÄĺ E º ³ ÈÍÍÍÍÍÍÍÍÍͼ ³ Pin 1 GroundÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ>GroundÄÄÄÄÄ> Pin 2 GroundÄÄÄÄÄÄÙ Circuit Copyright (C)1990 by Paul Reid ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º ADDING COLOR º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Adding color to this circuit would require a lot of extra parts. NTSC composite color involves matrixing the color components. The Chroma is modulated onto a 3.58 Mhz subcarrier. This is mixed with the main Luminance signal. Phase and amplitude must be carefully controlled. Cheap composite color monitors usually give poor text display. If I wanted color I would buy a real 9-pin RGB monitor. If you want to try to add color to this adapter, the LM1886 and LM1889 chips provide a partial solution. Good Luck! ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º BUGS º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Theorists may object that the video is a bit strong, at one volt instead of the seven tenths volts of standard video. But the IBM CGA composite output was similarly "hot". Works fine. "Proper" vertical sync pulses would have horizontal sync pulses embedded in them. My circuit doesn't provide this frill. These extra sync pulses were necessary for older TV sets working with weak noisy broadcast signals. Modern monitors directly connected usually do fine without them. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Page 2 R-G-B to Composite Converter (C) 1990 Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ The output impedance is a bit high, at 100 ohms. But this is only critical for "long" cables. If I wanted to drive more than ten or twenty feet of cable I might worry. I am using only three feet of cable... no problem. Your monitor should have a 75 ohm input termination. Most do. Some have a switch to choose 75 or HI - 75 should work better. If you use this adapter on an EGA card, try to force the card to CGA (640 x 200) mode. Usually there is a DIP switch or utility program to do this. Tell your programs you have a CGA, don't let them force EGA mode on. Pin 2 is ground on a CGA, but is an Enhanced video signal on the EGA, and this adapter won't Auto-Swtch to match the card's EGA mode. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º LIVING WITHOUT COLOR º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Of course it is not color. Red and green are instantly distinguishable on a color display, but are quite close on a monochrome display. Programs that use clashing colors for highlight can be hard to use. Some programs, when faced with a CGA card, go crazy with colors. Fortunately, most have an option for "mono monitor on color card", or similar. Or you may be able to set the "colors" to grey shades that work for you. Sometimes a command line option sets the mode- try /bw, /green, /amber, or /mono. Or read your program's manual (only as a last resort!). One of the PC-MAGazine utilities is MONO.COM. It sits in the background and studies the screen's colors, and changes them on the fly to more mono-compatable colors. You can see a screen come up kind of no-contrast, then resolve to high-contrast as MONO fixes it. Though it occasionally makes a poor choice of color, or conflicts with other programs, I recommend trying it. MONO.COM is available as a bonus with a subscription to PCMagazine, or on the ZNT: gateway on CompuServe. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Page 3 R-G-B to Composite Converter (C) 1990 Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º BUILDING IT º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Get these parts- 1- 9 pin D-sub male connector 276-1537 .99 1- hood for 9 pin D-sub connector 276-1513 1.49 1- 3 foot phono cable 42-2370 1.69 1- 2N4401 or 2N2222 or 2N3904 Transistor 276-2058 or 276-2009 or 276-2016 .49 1- 220 ohm resistor (Red-Red-Brown) 271-1313 .39 1- 470 ohm resistor (Yellow-Violet-Brown) 271-1317 .39 1- 680 ohm resistor (Blue-Grey-Brown) 271-021 .25 3- 1 K ohm resistors (Brown-Black-Red) 271-1321 (1 pack) .39 1- 1.5 K ohm resistor (Brown-Green-Red) 271-025 .25 2- feet thin stranded insulated wire -- ---- $6.33 Radio Shack part numbers are included for convenient identification. No endorsement is implied. All resistors may be 1/4 or 1/8 watt, 10% or 5%. The nearest available value may be substituted if need be. Transistor may be almost any fairly fast NPN switch. High gain, high power or low noise transistors may not be fast enough. Most of the resistors are mounted to the plug pins, as close to the plug body as possible. The numbers on the 9-pin connector I used were awful hard to see, and I did it wrong the first time. The chart "Tech's Eye View of 9-Pin RGB Connector" will help you avoid this pitfall. Also refer to "Pictorial View" as you work. Jumper pins 1 and 2 with a bit of bare wire. This will be ground. Solder a pair of 1 Kohm resistors to pins 8 and 9. Twist their free ends together, solder, and trim. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Page 4 R-G-B to Composite Converter (C) 1990 Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Solder these resistors- 220 ohm to pin 6 470 ohm to pin 3 1 Kohm to pin 4 1.5 Kohm to pin 5. Twist their free ends together, solder lightly, and trim. We will add a resistor, a transistor lead, and the core of the output cable to this junction. Leave a little free end to add these parts to. Twist one end of the 680 ohm resistor to the four-resistor junction you just soldered. Solder it. Trim the bare ends of the phono cable as short as possible. Pre- tin them with solder. Solder the outside shield of the phono cable to the bare wire on pins 1 and 2. Solder the inner core to the five- resistor junction. Figure out which lead is which on the transistor. The Emitter gets soldered to the ground wire. The Base connects to the two-resistor junction. The Collector connects to the five resistor junction. Though modern silicon transistors are quite tough, try not to cook it. Use a hot iron and work fast, but get a good joint. Shorten the free end of the 680 ohm resistor and solder the thin insulated wire to it. You need a plus five volt (four to twelve volt) source to bias the sync inverter. If your CGA card has a 6 pin header, with pin 2 missing, pin 5 has +5 volts. Pin 1 on a Game port is +5 volts too. For simplicity you could use four D-cell batteries in a holder such as Radio Shack 270-396 or 270-389. Connect the plus wire to the thin insulated wire from the 680 ohm resistor. Connect the minus wire to the bare wire on pins 1 and 2. D-cells will run continuously for a month, maybe a year if you put a switch in the plus wire and turn them off when you shut off the computer. Or use a plug-in DC power supply. Radio Shack #273-1552 will work. You may have an old calculator or toy power pack. Just be sure it puts out D.C., and 4 to 12 volts. Any hum or ripple in the power supply will show as bright horizontal bands moving slowly downward through the display. You should try to find one that is well filtered. Again, connect the plus wire to the thin insulated wire from the 680 ohm resistor. The minus wire goes to the bare wire on pins 1 and 2. If you aren't afraid to get inside your PC's case, get your plus five volts from your floppy disk drive. Pin 1 of the four pin connector on any standard disk drive is plus five volts. On most power supplies the wire to it is colored red. Solder your thin insulated wire to the back of pin 1 on the drive. Or peel a bit of insulation off of the power supply wire and tack-solder to it's core. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Page 5 R-G-B to Composite Converter (C) 1990 Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Now squeeze the whole assembly into the hood. Use little scraps of bubble-pack plastic to separate any bare leads that want to touch each other. If you use a metal or metalized hood, wrap a bit of plastic tape around all the parts so they don't ground out on the hood. You will probably have to pad out the phono cable with plastic tape where the cable clamp grips it. The clamp is made for much larger cables. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º TECH's EYE VIEW of 9-PIN RGB CONNECTOR º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ \ 5 4 3 2 1 / \ 9 8 7 6 / ÀÄÄÄÄÄÄÄÄÄÙ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º PICTORIAL VIEW OF CONNECTIONS º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ 9-Pin Conn. Resistors Transistor Outputs ÄÄÄÄÄÄÄÄÄÄÄ ÄÄÄÄÄÄÄÄÄ ÄÄÄÄÄÄÄÄÄÄ ÄÄÄÄÄÄÄ 1ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÂÄÄ> VideoGround >ÄÄÄÄÄ> 6ÄÄÄÄÄÄÄÄÄ220ohmÄÄÄÄÄÄÄ¿ ³ ³ 2ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³ ³ ÀÄÄ< PowerCommon <ÄÄÄÄÄ< 7ÄÄÄNC ³ ³ ÉÍÍÍÍÍÍ» 3ÄÄÄÄÄÄÄÄÄÄÄÄ470ohmÄÄÄÄÄÄÄ´ ÀĺE 2N º 8ÄÄÄÄÄÄÄÄÄ1KohmÄÄÄÄÂÄÄijÄÄÄÄĺB 2222º 4ÄÄÄÄÄÄÄÄÄÄÄÄ1KohmÄÄÄÄÄÄÄÄ´ ÚĺC º 9ÄÄÄÄÄÄÄÄÄ1KohmÄÄÄÄÙ ³ ³ ÈÍÍÍÍÍͼ 5ÄÄÄÄÄÄÄÄÄÄÄÄ1.5KohmÄÄÄÄÄÄÁÄÂÄÁÄÄÄÄÄÄÄÄÄÄÄ> Video Out >ÄÄÄÄÄ> ÚÄÄÄÄÄ680ohmÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ< +5 Volts In <ÄÄÄÄÄ< ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Page 6 R-G-B to Composite Converter (C) 1990 Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º USING IT º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ Plug it in and turn on the PC and monitor. The default DOS colors are medium white on black. Trim your brightness and contrast controls so the background is black but on the verge of glowing, and the characters are medium bright. I usually adjust the brightness so I can see the background scan lines if I look for them, but so they don't distract from normal viewing. This gives best separation of medium grey tones. If the monitor "smears" the highlights, be sure you have a 75 ohm termination. You might also try adding a 100 ohm resistor from the center of the output cable to ground. Some old monitors were really tunerless TV sets and couldn't help "smearing". The Width and Height controls may want tweeking. Be sure you have a full screen image when you set these. The image on lower cost monitors may shrink and swell a bit as the brightness changes. The enclosed program, LINE-UP.EXE, will help set up your monitor. Just run it. You will see all 128 pairs of background colors (8) and foreground colors (16). Naturally Black on Black, etc, will be hard to read, but all the other pairs should resolve as separate grey values if the Brightness and Contrast are set properly. The Border lines use all 80 columns and 25 lines and should be visible. LINE-UP.EXE can also be used to adjust color displays on color video adaptors. On a good RGB monitor the colors should mostly look just like their names. On most composite color monitors you can only approximate the ideal colors. Composite video can also be fed into TV sets and VCRs. You will find that few TVs can display legible 80 column text, and many VCRs will have trouble with the simplified sync pulses. ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ» º DISCLAIMER º ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ This is an experimental, do-it-yourself device. If your monitor acts funny, shut it off and figure out what is wrong. Using this cable is sure to break any warranty on your monitor or PC. If it smokes or dies, don't call me. Radio Shack is a trademark, and their part numbers are referenced only for easy identification. No endorsement should be construed. But it has worked for me on several different PCs and monitors, saved me a lot of money, and I hope it can do the same for you. Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Page 7 R-G-B to Composite Converter (C) 1990 Paul Reid ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ